CO2 ile bitki gübreleme
Bitkilerinizin aç kalmasına izin vermeyin!
Bitkileriniz doğru ışığı alır almaz fotosentez işlemine başlarlar. Sonuç olarak, karbondioksit (CO2) beslenmeyi (şeker) yapmak için suyla birleştirilir ve yan ürün olarak oksijen (O2) salınır. Bu şekilde CO2, bitkilere ana besin maddesi olarak hizmet eder. Diğer gübreler, örneğin JBL PROFLORA Ferropol ya da JBL PROFLORA Ferropol 24 ne kadar yağ, karbonhidrat ve protein (bitkiler için CO2'e karşılık gelir) yediğimiz önemli değil, insanların hayatta kalmak için ihtiyaç duydukları vitaminler ve eser elementlerle karşılaştırılabilir.
CO2, akvaryum suyunuzda balıkların, bitkilerin (gece), omurgasızların ve bakterilerin solunması yoluyla her zaman küçük miktarlarda bulunur.
Where does the natural CO2 content in the water come from?
Can you leave out the CO2?
Admittedly, even without CO2 fertilisation, some aquarists have observed their plants growing. There are several reasons for this, and the needs of aquarium plants can differ as much as those of fish (discus/goldfish). Some plants, such as the Vallisneria, need very little fertiliser, little light and can survive with the CO2 content of untreated water. Any high maintenance plants, such as Rotala macranda, would perish miserably if forced to share an aquarium in these conditions. The Vallisneria, on the other hand, would flourish still further, were it to receive CO2 fertilisation, assuming there is enough fertiliser and light.
CO2 is dissolved in EVERY water, as it diffuses from our air into the water until the CO2 content in the water is equal to the CO2 content in the air (concentration balance). Unfortunately, it’s not enough for most aquarium plants.
Akvaryum suyunuzda ne kadar CO2 var?
Bu tablo size şunları gösterir: öncelikle akvaryum suyunuzda ne kadar CO2 çözüldüğünü ve ikinci olarak da hangi CO2 içeriğinin bitkileriniz için ideal olduğunu gösterir. Tabloyu kullanmak için, akvaryum suyunuzun pH değerine ve karbonat sertliğine ihtiyacınız vardır. Bu iki değer size okunması kolay bir CO2 içeriği verecektir. Örneğin, pH içeriğiniz 7.4 ve KH 6 ° dKH ise, suda 7 mg / 1 C02 vardır. Bununla birlikte, çoğu su bitkisi, kuvvetli ve sağlıklı bir büyüme için 14 ila 23 mg / 1 arasında biraz daha yüksek CO2 seviyelerine ihtiyaç duyar. Çok hassas türlerin bile 23 - 36 mg / l'ye ihtiyacı vardır. Bir CO2 gübre sistemi sayesinde, sudaki CO2 içeriğini artırabilir ve böylece aynı zamanda balıklarınız için mükemmel pH değerini sağlayabilirsiniz.
Akvaryum suyunuzun pH değerini ölçtüğünüzde, akvaryumunuzda ne kadar CO2 bulunduğunu gösterilen tablodan yardım alabilirsiniz. Tablodaki yeşil alan, gelişen bitki gelişimi için ideal CO2 seviyesinin ne olacağını veya hassas bitkiler için doğru seviyenin ne olacağını gösterir. Artık suyunuzun CO2 içeriğinin yeterli olup olmadığını görebilirsiniz; mükemmel bitki gelişimi için miktarı artırmanız gerekir. JBL size pratik bir uygulama sunuyor JBL CO2-pH Permanent testi , ile akvaryum suyunuzun CO2 içeriğini kalıcı olarak görebilirsiniz. Bu sayede sudaki CO2 miktarını istediğiniz zaman kolayca ve hızlıca okuyabilirsiniz.
CO2 konsantrasyonunun artması için aşağıdaki gübre sistemlerini bulabilirsiniz. PROFLORA CO2 bitki bakımı . Biyo-CO2 sistemleri arasından seçebilrisiniz ( PROFLORA Bio ), Şeker mayası sistemi ve CO2 ile doldurulmuş basınçlı gaz tüplü sistemler vasıtasıyla CO2 elde edebilirsiniz ( kullan-at (u) ya da doldurulabilir (m) ).
In addition, you still have the option of purchasing a CO2 set, which includes everything but a CO2 cylinder ( JBL PROFLORA CO2 PROFESSIONAL SET V ). This is especially interesting if you already own a CO2 cylinder.
CO2 gübreleme sistemi şu şekilde çalışır
For CO2 fertiliser systems with pressurised gas cylinders you have the choice between disposable cylinders as JBL ProFlora u-System ( kullan-at (u) ) and refillable returnable cylinders as JBL ProFlora m-System ( doldurulabilir (m) ).
CO2, basınç altında sıvılaştırıldığından, daima dik konumda tutulması gereken bir depolama silindirindedir. Akvaryuma verilan gazı iyi dozda tutmak için, basınç düşürücüyü depolama silindirine takın. Silindir basıncını azaltır, böylece CO2 beslemesini küçük bir düğme ile tam bir kabarcık miktarına ayarlayabilmenizi sağlar. CO2, basınç düşürücüsünden CO2 dirençli bir hortum üzerinden, aynı zamanda çek valf olarak işlev gören bir kabarcık sayacına ulaşır ( JBL PROFLORA CO2 Count Safe ). Sayaç içinde, CO2 kabarcıklarının yükseldiği ve görünür hale geldiği su bulunur. Artık istediğiniz kabarcık sayısını düğme ile ayarlayabilirsiniz. Entegre çek valf, suyun basınç düşürücü ve depolama silindirine geri akışını önler. CO2 hortumu, karbondioksiti, basınç düşürücüden akvaryumunuza, suyun içinde mümkün olduğu kadar çabuk ve homojen bir şekilde çözülmesi gereken akvaryumunuza taşır. Bunun için akvaryumunuzun boyutuna bağlı olarak çeşitli difüzörler mevcuttur. Difüzörde CO2, çözündüğü akvaryum suyuyla temas eder. Kalıcı bir test ne kadar suyun çözüldüğünü ve bunun doğru miktar olup olmadığını gösterir.
Connecting a CO2 system, aerating the aquarium and putting it into operation
What are the advantages of a CO2 plant fertiliser system? How do you connect a CO2 fertiliser system to your aquarium? Why should you aerate your aquarium at night?
Which CO2 system is the right one for you?
CO2, also called carbon dioxide, is the main nutrient for all plants.
Bio-CO2 systems produce the plant nutrient carbon dioxide (CO2) through a biological reaction process in which (simply formulated) yeast reacts with sugar. The reaction components can be renewed after about 40 days.
For CO2 fertiliser systems with pressurised gas cylinders you have the choice between disposable cylinders as JBL ProFlora u-System ( kullan-at (u) ) and refillable returnable cylinders as JBL ProFlora m-System ( doldurulabilir (m) ).
These systems contain the plant nutrient carbon dioxide (CO2) in a pressurised gas cylinder which you simply replace when it is empty.
These systems contain the plant nutrient carbon dioxide (CO2) in a pressurised gas cylinder which you can have refilled once empty.
The ideal CO2 fertilisation for plants in the aquarium
CO2, also called carbon dioxide, is the main nutrient for all plants.
What is the significance of the individual components of a CO2 system?
The CO2 is available as a gas either in compressed form in disposable ( JBL PROFLORA CO2 CYLINDER 500 U ) or refillable ( JBL PROFLORA CO2 CYLINDER 500 M ) cylinders, or as biogas produced by a sugar-yeast reaction in a reaction vessel ( PROFLORA CO2 BIO ) produziert wird.
To reduce the pressure from the compressed gas cylinder, a pressure reducer is screwed on there ( JBL PROFLORA CO2 REGULATOR BASIC , JBL PROFLORA CO2 REGULATOR ADVANCED , JBL PROFLORA CO2 REGULATOR PROFESSIONAL It reduces the 50-60 bar cylinder pressure to a working pressure of approx. 1.2 bar. This 1.2 bar is then dosed by a small handwheel (fine needle valve) so precisely that individual CO2 bubbles can be seen and counted in a bubble counter. The cylinder pressure and the working pressure are indicated on pressure gauges on the pressure reducer (NOT with the JBL PROFLORA CO2 REGULATOR BASIC ).
These displays are not strictly necessary, as - unlike with diving cylinders with compressed air - the cylinder pressure does not slowly drop, and you do not need to be warned when the cylinder is running low. Instead, the pressure remains at its maximum pressure and then drops to zero quite quickly. So, unfortunately, there is hardly any slow decrease in the cylinder filling pressure.
The working pressure would only be important if it had to be adjusted. But this is normally not necessary. But somehow most people are happier having two pressure gauges giving them readings. JBL also offers a minimalist pressure reducer without a pressure gauge ( JBL PROFLORA CO2 REGULATOR BASIC ). If you would like to equip your pressure reducer with a solenoid valve for night switch-off or pH control, you can buy it complete with the solenoid valve already fitted ( JBL PROFLORA CO2 REGULATOR ADVANCED ). Of course it would also be possible to RETROFIT an existing pressure reducer with a solenoid valve ( JBL PROFLORA CO2 VALVE ). ALL JBL PROFLORA CO2 REGULATOR types are supplied with the adapter from the U to the M system (the adapter must then simply be unscrewed using an Allen key). If you have a Dennerle pressure reducer for Dennerle disposable cylinders, you can make the Dennerle pressure reducer suitable for JBL disposable cylinders with the aid of the adapter JBL PROFLORA CO2 ADAPT U - Dennerle Adapting Dennerle pressure reducesr to fit JBL disposable cylinders.
| Pressure reducer type: | Pressure gauge | Solenoid valve | Adapter u-m |
|---|---|---|---|
| JBL PROFLORA CO2 REGULATOR BASIC | no | no | yes |
| JBL PROFLORA CO2 REGULATOR ADVANCED | yes | no | yes |
| JBL PROFLORA CO2 REGULATOR PROFESSIONAL | yes | yes | yes |
Lay the hose connections so that they are as short as possible. The shorter the CO2-carrying hoses, the faster the whole system will react when you increase or decrease the pressure on the fine needle valve. Even with short hoses, however, your settings will always have a delayed reaction. Do not turn the fine needle valve of the pressure reducer too much. Adjust it slightly and wait a little before the bubble count in the bubble counter ( JBL PROFLORA CO2 TAIFUN COUNT SAFE ) changes. CO2 hoses also harden over time and then need to be replaced. JBL has dedicated CO2 resistant hoses: JBL PROFLORA CO2 TAIFUN TUBE in black and transparent.
Since CO2 gas is not visible, but we want to add it in doses, we have to make it visible. In the JBL CO2 concept there are several options: JBL has the JBL PROFLORA CO2 TAIFUN COUNT SAFE , a bubble counter with an integrated check valve. The bubble counter is filled with water through which the CO2 bubbles rise to the top. In this way they can easily be dosed and counted. In all JBL CO2 diffusers Bubble counters ( JBL PROFLORA CO2 TAIFUN GLASS , JBL PROFLORA CO2 TAIFUN SPIRAL 5 and JBL PROFLORA CO2 TAIFUN INLINE ) the CO2 bubbles can be counted, but in the case of the JBL PROFLORA TAIFUN GLASS only after a little running time (once enough water has collected in the glass body). If the diffusers are not easily visible, it may be advisable to mount a separate bubble counter.
To prevent the aquarium water from entering the hose and flowing towards the technical equipment, a check valve ( JBL PROFLORA SafeStop ) needs to be fitted as closely as possible to the aquarium, ideally directly above the water surface. The CO2 gas dissolves so easily in the water that it diffuses out of the hose into the aquarium water when the cylinder is empty or the supply is turned off, and thus migrates in the hose towards the cylinder. If a JBL PROFLORA CO2 TAIFUN COUNT SAFE or a JBL PROFLORA CO2 TAIFUN INLINE is installed in which check valves are integrated, no further check valve is required.
In the aquarium, the CO2 gas now needs to be dissolved in the water so that it can serve the plants as their staple food. For this purpose there are several options available: In the simplest JBL Bio-CO2 set ( JBL PROFLORA CO2 STARTER BIO SET ), an air stone is used. The CO2 bubbles are of different sizes and a slight loss of CO2 occurs as some bubbles reach the water surface. In the JBL PROFLORA CO2 TAIFUN GLASS a connection to the water is made by a ceramic disc. The CO2 is pressed through in tiny bubbles and dissolves in the aquarium water on its way to the water surface. For this reason, CO2 diffusers should always be installed as low as possible below the surface. The only exception is the JBL PROFLORA CO2 TAIFUN INLINE , which is integrated into the water-returning hose of the external filter. It also has a ceramic diaphragm through which the CO2 enters the water and dissolves on its way back from the filter into the aquarium.
In the JBL PROFLORA CO2 TAIFUN SPIRAL 5 and JBL PROFLORA CO2 TAIFUN SPIRAL 10 the CO2 bubbles rise upwards like in a spiral driveway of a multi-storage car park, then dissolve in the parking garage i.e. in the aquarium water. A few bubbles still reach the top, but they hardly contain any CO2. On their way up the bubbles also absorb gases from the aquarium water (O2, N2 etc.), so don't worry about wasting too much CO2! In case you are worried, the bubble remains are collected in a chamber at the top☺. Both diffusers TAIFUN SPIRAL 5 and SPIRAL 10 can be extended with modules ( JBL PROFLORA CO2 TAIFUN SPIRAL EXTEND ), if your aquarium requires more CO2 or if you are changing to a larger aquarium. The length of the CO2 reactors is only limited by the aquarium height.
Since plants only need CO2 for photosynthesis during the lighting phase, you can turn off the CO2 supply at night. To save you having to turn the CO2 cylinder or the fine needle valve on and off, there is a solenoid valve ( JBL PROFLORA CO2 VALVE ), which can be controlled by a timer. The timer then switches the light and the CO2 supply on with the solenoid valve in the morning and off again in the evening. Anyone with a good head for figures will soon realise that the solenoid valve quickly recoups its cost price by saving the CO2 by about half. It is always installed between pressure reducer and check valve. If you want to use a CO2/pH computer with an automatic CO2 control, you’ll also need a CO2 solenoid valve. This is then not switched via the timer, but via the CO2/pH control unit ( JBL PROFLORA CO2 CONTROL ). In some CO2 sets the solenoid valve is already included ( JBL PROFLORA CO2 ADVANCED SET M and JBL PROFLORA CO2 PROFESSIONAL SET M ).
A CO2 solenoid valve can be retrofitted to any CO2 fertiliser system (except Bio-CO2) at any time. It is simply inserted into the hose directly behind the pressure reducer. Cut the hose, insert the solenoid valve - done.
If you want to automate the CO2 supply, you can connect a pH computer ( JBL PROFLORA CO2 CONTROL ) instead of a timer for the night switch-off. You have to enter the carbonate hardness (KH) of your aquarium water once (test with JBL PROAQUATEST KH Karbonat Sertliği testi and then the computer calculates the matching pH value, which is adjusted by adding CO2 (some of the CO2 reacts in the water to form carbonic acid, which then lowers the pH value). At this "suitable" pH value, the optimal CO2 content of about 30 mg/l for perfect plant growth is always ensured. The computer then controls the solenoid valve and adds as much CO2 until the calculated or desired pH value is reached. The solenoid valve is then closed and opened again so that the pH value remains stably adjusted. Since the pH value drops automatically at night, the computer also stops adding CO2 at night through the solenoid valve. The pH measurement of the water is done via a pH electrode, which is NOT included in the set and needs to be purchased separately. This ensures that you do not receive an old electrode in the set, but always a factory-fresh one!
Every pH control or measuring device, including the JBL CO2/pH control unit ( JBL PROFLORA CO2 CONTROL ) requires a pH electrode ( JBL PROFLORA CO2 pH SENSOR SET ) to measure the pH value of the water. pH electrodes age with time and must be replaced about every 2 years. Every 30-45 days the pH electrode needs to be calibrated so that it continues to show accurate values. During calibration, the functionality of the electrode is also checked so that you know when a new electrode is needed.
If you add CO2 to your aquarium, the amount of CO2 in the aquarium water also needs to be controlled, as too little CO2 will not help your plants and too much CO2 can be dangerous for fish and invertebrates. The correct amount can be permanently displayed to you with the help of a permanent test ( JBL PROAQUATEST CO2-pH Sabit ), which is placed in the aquarium. In addition to the CO2 content, the test can also show you the pH value of your water, provided you have not added any other pH-lowering agents such as pH-Minus apart from CO2. Please note that this test displays correctly with a delay! The CO2 gas must first react from the aquarium water through a small air bell in the test vessel with the reagent liquid contained. So do not change the amount of CO2 and expect an immediate colour change of the reagent in the test! This test is elementary when using CO2 systems (except for Bio-CO2 systems), because only via this test an overdosage is indicated. When using a CO2/pH control unit, the test is not necessary, as the computer prevents overdosing.
To calibrate pH electrodes you need liquids with a fixed pH value. The JBL set ( JBL PROFLORA CO2 CALIBRATION SET ) contains all the liquids you need: For a routine calibration, during the calibration process displayed in the pH control unit, dip the electrode first into the JBL Tampon çözelti pH 7,0 and then into the JBL Tampon çözelti pH 4,0 . Rinse briefly with distilled water (e.g. JBL Dest ) in between and at the end - done.
There are 2 different cylinder types: disposable cylinders that are disposed of and recycled after emptying and reusable cylinders that can be refilled again and again. Many pet shops and gas companies can carry out the refilling. If you, for example, live in a region where refilling is a problem, the disposable cylinder would be an alternative. Should the refilling situation improve, you can always convert the pressure reducer of the disposable cylinder into a reusable one in 2 minutes by unscrewing the adapter ( JBL PROFLORA CO2 ADAPT U - M ). Aquarists who live on islands, for instance, are sometimes not allowed to transport filled reusable cylinders on the ferry or plane. JBL CO2 disposable cylinders are then sometimes allowed!
The size of the cylinder often depends on the cabinet in which the CO2 storage cylinder is to be placed: A 500 g disposable cylinder is only 31 cm high (plus pressure reducer = 37 cm), a 500 g reusable cylinder with stand is already 43 cm high and a 2000 g bottle 45.5 cm high. Basically, of course, a larger cylinder is an advantage, because it needs to be replaced or refilled less frequently.
All reusable CO2 cylinders must be inspected regularly, every 10 years, by the TÜV (at least in Germany). On the cylinder you will always find - sometimes badly legibly - the date of the last TÜV inspection and sometimes the year of the next inspection.
The term hysteresis refers to the delayed switching of the solenoid valve for the desired pH value. For example, if you have set a pH value of 6.0 (your desired pH value), the unit still needs to know when to add CO2 to reach the pH value and when to switch off when it has been reached. As a rule, the hysteresis is 0.5 pH units. For example, if the pH value is 6.5, the CO2 addition is switched on until the pH value reaches 5.5 due to the added CO2. Then the CO2 addition is switched off. With the JBL PROFLORA CO2 CONTROL , you can also increase or decrease the hysteresis by 0.1 increments if you wish. In our example, the unit then switches the CO2 supply on at 6.1 pH and off again at 5.9. A hysteresis of 0 would make no sense, as the solenoid valve would then switch on and off permanently. After all, the added CO2 also needs a certain amount of time to influence the pH value.
Since CO2 is a gas, you can simply use an airstone to add this gas to the water (as in the JBL PROFLORA CO2 STARTER BIO SET ). However, there is of course some loss of CO2, as the larger CO2 bubbles do not dissolve completely in the water on their way to the surface.
So it makes sense to reduce the size of the bubbles in order to make them dissolve better. This is achieved with a diffuser that has a ceramic plate through which the CO2 is forced. The very small CO2 bubbles dissolve more quickly in the water and the CO2 loss is minimised considerably. If the carbonate hardness of the water is not too high, such a diffuser ( JBL PROFLORA CO2 TAIFUN GLASS ) can be used for aquarium contents of up to 300 litres. If the ideal CO2 content indicated by the CO2 permanent test can not be reached, either the CO2 consumption by the aquarium plants is extremely high or the water hardness (KH) is so high that the amount of CO2 added is not sufficient.
The JBL PROFLORA CO2 TAIFUN SPIRAL 5 or JBL PROFLORA CO2 TAIFUN SPIRAL 10 is suitable for any size of aquarium assuming the height fits. In addition, it has the advantage that it can be extended in length, and thus in its performance, by adding further modules.
How does the CO2 get into the water?
The main plant nutrient CO2 is a gas that can be dissolved in water with the help of CO2 diffusers or CO2 reactors.
A lot of pet shops, in emergencies also fire brigades or gas retailers, can refill your CO2 reusable cylinders. The pressure gauge shows you if the pressure has decreased. Sometimes an instant refill is just not possible, but there’s an easy solution for that too. If you have a disposable 500g cylinder ( JBL PROFLORA u500 ) as spare cylinder in stock, you can integrate it within a few seconds. Even if you have a refillable JBL m system you can adapt your pressure reducer to the disposable cylinder with one simple movement using an Allen key.
JBL PROFLORA CO2 Premium Service Partner
In the dealer search below, you can find out which specialist dealer in your area carries the JBL PROFLORA CO2 concept and can help you fill or exchange the JBL PROFLORA CO2 cylinders by entering your postal code.